Martin Sperl [Fri, 2 Sep 2016 15:45:27 +0000 (16:45 +0100)]
Register the clocks early during the boot process,
so that special/critical clocks can get enabled early on
in the boot process avoiding the risk of disabling a clock,
pll_divider or pll when a claiming driver fails to install
propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Noralf Trønnes [Fri, 7 Oct 2016 14:50:59 +0000 (16:50 +0200)]
watchdog: bcm2835: Support setting reboot partition
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Eric Anholt [Tue, 10 May 2016 00:28:18 +0000 (17:28 -0700)]
clk: bcm2835: Mark GPIO clocks enabled at boot as critical.
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
v2: Skip marking as critical if they aren't on at boot.
Noralf Trønnes [Sat, 3 Oct 2015 20:22:55 +0000 (22:22 +0200)]
dmaengine: bcm2835: Load driver early and support legacy API
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Phil Elwell [Wed, 24 Jun 2015 13:10:44 +0000 (14:10 +0100)]
spi-bcm2835: Support pin groups other than 7-11
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Phil Elwell [Fri, 6 May 2016 11:32:47 +0000 (12:32 +0100)]
pinctrl-bcm2835: Return pins to inputs when freed
When dynamically unloading overlays, it is important that freed pins are
restored to being inputs to prevent functions from being enabled in
multiple places at once.
Phil Elwell [Thu, 26 Feb 2015 09:58:22 +0000 (09:58 +0000)]
pinctrl-bcm2835: Only request the interrupts listed in the DTB
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Phil Elwell [Tue, 24 Feb 2015 13:40:50 +0000 (13:40 +0000)]
pinctrl-bcm2835: Fix interrupt handling for GPIOs 28-31 and 46-53
Contrary to the documentation, the BCM2835 GPIO controller actually has
four interrupt lines - one each for the three IRQ groups and one common. Rather
confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
46-53 GPIO2.
Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
cleaner to split out a function to process the interrupts for a single GPIO
bank.
This bug has only just been observed because GPIOs above 27 can only be
accessed on an old Raspberry Pi with the optional P5 header fitted, where
the pins are often used for I2S instead.
Noralf Trønnes [Fri, 12 Jun 2015 17:01:05 +0000 (19:01 +0200)]
irqchip: bcm2835: Add FIQ support
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Elwell [Fri, 4 Dec 2015 17:41:50 +0000 (17:41 +0000)]
irq-bcm2836: Prevent spurious interrupts, and trap them early
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
Eric Anholt [Fri, 19 Dec 2014 00:07:15 +0000 (16:07 -0800)]
mm: Remove the PFN busy warning
See commit dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
The compacted-format XSAVES area is determined at boot time and
never changed after. The field xsave.header.xcomp_bv indicates
which components are in the fixed XSAVES format.
In fpstate_init() we did not set xcomp_bv to reflect the XSAVES
format since at the time there is no valid data.
However, after we do copy_init_fpstate_to_fpregs() in fpu__clear(),
as in commit:
b22cbe404a9c x86/fpu: Fix invalid FPU ptrace state after execve()
and when __fpu_restore_sig() does fpu__restore() for a COMPAT-mode
app, a #GP occurs. This can be easily triggered by doing valgrind on
a COMPAT-mode "Hello World," as reported by Joakim Tjernlund and
others:
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5f8 ("tcp: fix mark propagation with fwmark_reflect enabled") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, RST packets generated by the TCP stack for non-existing
sockets always have mark 0.
The mark from the original packet is assigned to the netns_ipv4/6
socket used to send the response so that it can get copied into the
response skb when the socket sends it.
Fixes: e110861f8609 ("net: add a sysctl to reflect the fwmark on replies") Cc: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.
Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info when ...") Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when ...") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an IPv6 version of commit 24803f38a5c0 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.
Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().
Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(
L2TP should use its own handler, because it really does not
look the same.
SIOCINQ for instance should not assume UDP checksum or headers.
Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.
While crashes only happen on recent kernels (after commit 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.
Fixes: 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue") Fixes: 85584672012e ("udp: Fix udp_poll() and ioctl()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dsa_slave_create() can fail, and dsa_user_port_unapply() will properly check
for the network device not being NULL before attempting to destroy it. We were
not setting the slave network device as NULL if dsa_slave_create() failed, so
we would later on be calling dsa_slave_destroy() on a now free'd and
unitialized network device, causing crashes in dsa_slave_destroy().
Fixes: 83c0afaec7b7 ("net: dsa: Add new binding implementation") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link layer protocols may unconditionally pull headers, as Ethernet
does in eth_type_trans. Ensure that the entire link layer header
always lies in the skb linear segment. tpacket_snd has such a check.
Extend this to packet_snd.
Variable length link layer headers complicate the computation
somewhat. Here skb->len may be smaller than dev->hard_header_len.
Round up the linear length to be at least as long as the smallest of
the two.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack must not pass packets to device drivers that are shorter
than the minimum link layer header length.
Previously, packet sockets would drop packets smaller than or equal
to dev->hard_header_len, but this has false positives. Zero length
payload is used over Ethernet. Other link layer protocols support
variable length headers. Support for validation of these protocols
removed the min length check for all protocols.
Introduce an explicit dev->min_header_len parameter and drop all
packets below this value. Initially, set it to non-zero only for
Ethernet and loopback. Other protocols can follow in a patch to
net-next.
Fixes: 9ed988cd5915 ("packet: validate variable length ll headers") Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because when tunnel->dst_cache init fails, we free dev->tstats
once in ipip6_tunnel_init() and twice in sit_init_net(). This looks
redundant but its ndo_uinit() does not seem enough to clean up everything
here. So avoid this by setting dev->tstats to NULL after the first free,
at least for -net.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An error was reported upgrading to 4.9.8:
root@Typhoon:~# ip route add default table 210 nexthop dev eth0 via 10.68.64.1
weight 1 nexthop dev eth0 via 10.68.64.2 weight 1
RTNETLINK answers: Operation not supported
The problem occurs when CONFIG_LWTUNNEL is not enabled and a multipath
route is submitted.
The point of lwtunnel_valid_encap_type_attr is catch modules that
need to be loaded before any references are taken with rntl held. With
CONFIG_LWTUNNEL disabled, there will be no modules to load so the
lwtunnel_valid_encap_type_attr stub should just return 0.
Fixes: 9ed59592e3e3 ("lwtunnel: fix autoload of lwt modules") Reported-by: pupilla@libero.it Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Popov reported that an application may trigger a BUG_ON in
sctp_wait_for_sndbuf if the socket tx buffer is full, a thread is
waiting on it to queue more data and meanwhile another thread peels off
the association being used by the first thread.
This patch replaces the BUG_ON call with a proper error handling. It
will return -EPIPE to the original sendmsg call, similarly to what would
have been done if the association wasn't found in the first place.
Acked-by: Alexander Popov <alex.popov@linux.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame and the following message may be logged:
NOHZ: local_softirq_pending 08
The problem is the same as what was described in commit ec13ee80145c
("virtio_net: invoke softirqs after __napi_schedule") and this patch
applies the same fix to mlx4.
Fixes: 07841f9d94c1 ("net/mlx4_en: Schedule napi when RX buffers allocation fails") Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com> Suggested-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Read this value once and cache locally, as it can be updated between
the test and use (TOCTOU).
Signed-off-by: Willem de Bruijn <willemb@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> CC: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry reported use-after-free in ip6_datagram_recv_specific_ctl()
A similar bug was fixed in commit 8ce48623f0cf ("ipv6: tcp: restore
IP6CB for pktoptions skbs"), but I missed another spot.
tcp_v6_syn_recv_sock() can indeed set np->pktoptions from ireq->pktopts
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov reported out of bound accesses in ip6gre_err()
If GRE flags contains GRE_KEY, the following expression
*(((__be32 *)p) + (grehlen / 4) - 1)
accesses data ~40 bytes after the expected point, since
grehlen includes the size of IPv6 headers.
Let's use a "struct gre_base_hdr *greh" pointer to make this
code more readable.
p[1] becomes greh->protocol.
grhlen is the GRE header length.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()
Fixes: 20e2a8648596 ("cipso: handle CIPSO options correctly when NetLabel is disabled") Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Paul Moore <paul@paul-moore.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov got crashes in __ip_options_echo() when a NULL skb->dst
is accessed.
ipv4_pktinfo_prepare() should not drop the dst if (evil) IP options
are present.
We could refine the test to the presence of ts_needtime or srr,
but IP options are not often used, so let's be conservative.
Thanks to syzkaller team for finding this bug.
Fixes: d826eb14ecef ("ipv4: PKTINFO doesnt need dst reference") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: b90e5794c5bd ("net: dont call jump_label_dec from irq context") Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW GMAC databook says the following about bits in "Register 15 (Interrupt
Mask Register)":
--------------------------->8-------------------------
When set, this bit __disables_the_assertion_of_the_interrupt_signal__
because of the setting of XXX bit in Register 14 (Interrupt
Status Register).
--------------------------->8-------------------------
In fact even if we mask one bit in the mask register it doesn't prevent
corresponding bit to appear in the status register, it only disables
interrupt generation for corresponding event.
But currently we expect a bit different behavior: status bits to be in
sync with their masks, i.e. if mask for bit A is set in the mask
register then bit A won't appear in the interrupt status register.
This was proven to be incorrect assumption, see discussion here [1].
That misunderstanding causes unexpected behaviour of the GMAC, for
example we were happy enough to just see bogus messages about link
state changes.
So from now on we'll be only checking bits that really may trigger an
interrupt.
[1] https://lkml.org/lkml/2016/11/3/413
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Phil Reid <preid@electromag.com.au> Cc: David Miller <davem@davemloft.net> Cc: Alexandre Torgue <alexandre.torgue@gmail.com> Cc: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting is a high precedence operation but "off" and "i" are in terms of
bytes so we need to have some parenthesis here.
Fixes: fbfa743a9d2a ("ipv6: fix ip6_tnl_parse_tlv_enc_lim()") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First one is that pskb_may_pull() may reallocate skb->head,
so the 'raw' pointer needs either to be reloaded or not used at all.
Second issue is that NEXTHDR_DEST handling does not validate
that the options are present in skb->data, so we might read
garbage or access non existent memory.
With help from Willem de Bruijn.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current version, the matchall internal state is split into two
structs: cls_matchall_head and cls_matchall_filter. This makes little
sense, as matchall instance supports only one filter, and there is no
situation where one exists and the other does not. In addition, that led
to some races when filter was deleted while packet was processed.
Unify that two structs into one, thus simplifying the process of matchall
creation and deletion. As a result, the new, delete and get callbacks have
a dummy implementation where all the work is done in destroy and change
callbacks, as was done in cls_cgroup.
Fixes: bf3994d2ed31 ("net/sched: introduce Match-all classifier") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modifying TIR hash should change selected fields bitmask in addition to
the function and key.
Formerly, Only on ethool mlx5e_set_rxfh "ethtoo -X" we would not set this
field resulting in zeroing of its value, which means no packet fields are
used for RX RSS hash calculation thus causing all traffic to arrive in
RQ[0].
On driver load out of the box we don't have this issue, since the TIR
hash is fully created from scratch.
Reported-by: Zhang Yanmin <yanmin.zhang@intel.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei had his box explode because doing read() on a package
(rapl/uncore) event that isn't currently scheduled in ends up doing an
out-of-bounds load.
Rework the code to more explicitly deal with event->oncpu being -1.
The -o/--order option is to select column number to sort a diff result.
It does the job by adding a hpp field at the beginning of the sort list.
But it should not be added to the output field list as it has no
callbacks required by a output field.
During the setup_sorting(), the perf_hpp__setup_output_field() appends
the given sort keys to the output field if it's not there already.
Originally it was checked by fmt->list being non-empty. But commit 3f931f2c4274 ("perf hists: Make hpp setup function generic") changed it
to check the ->equal callback.
Anyways, we don't need to add the pseudo hpp field to the output field
list since it won't be used for output. So just skip fields if they
have no ->color or ->entry callbacks.
Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Fixes: 3f931f2c4274 ("perf hists: Make hpp setup function generic") Link: http://lkml.kernel.org/r/20170118051457.30946-1-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 21e6d8428664 ("perf diff: Use perf_hpp__register_sort_field
interface") changed list_add() to perf_hpp__register_sort_field().
This resulted in a behavior change since the field was added to the tail
instead of the head. So the -o option is mostly ignored due to its
order in the list.
This patch fixes it by adding perf_hpp__prepend_sort_field().
Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Fixes: 21e6d8428664 ("perf diff: Use perf_hpp__register_sort_field interface") Link: http://lkml.kernel.org/r/20170118051457.30946-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That's happening because each printk() call now gets printed on its own
line, and we do a separate call to print the spaces before the symbol.
Fix it by doing the printk() directly instead of using the
print_ip_sym() helper.
Additionally, the symbol address isn't very helpful, so let's get rid of
that, too. The final result looks like this:
our SMT scheduling topology for Fam17h systems is broken, because
the ThreadId is included in the ApicId when SMT is enabled.
So, without further decoding cpu_core_id is unique for each thread
rather than the same for threads on the same core. This didn't affect
systems with SMT disabled. Make cpu_core_id be what it is defined to be.
restored the initial approach we had with the Fam15h topology of
enumerating CU (Compute Unit) threads as cores. And this is still
correct - they're beefier than HT threads but still have some
shared functionality.
Our current approach has a problem with the Mad Max Steam game, for
example. Yves Dionne reported a certain "choppiness" while playing on
v4.9.5.
That problem stems most likely from the fact that the CU threads share
resources within one CU and when we schedule to a thread of a different
compute unit, this incurs latency due to migrating the working set to a
different CU through the caches.
When the thread siblings mask mirrors that aspect of the CUs and
threads, the scheduler pays attention to it and tries to schedule within
one CU first. Which takes care of the latency, of course.
CONFIG_KASAN=y needs a lot of virtual memory mapped for its shadow.
In that case ptdump_walk_pgd_level_core() takes a lot of time to
walk across all page tables and doing this without
a rescheduling causes soft lockups:
The commit caused a regression on LINE6 Transport that has no control
caps. Although reverting the commit may result back in a spurious
error message for some device again, it's the simplest regression fix,
hence it's taken as is at first. The further code fix will follow
later.
Fixes: f6a0dd107ad0 ("ALSA: line6: Only determine control port properties if needed") Reported-by: Igor Zinovev <zinigor@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_seq_pool_done() syncs with closing of all opened threads, but it
aborts the wait loop with a timeout, and proceeds to the release
resource even if not all threads have been closed. The timeout was 5
seconds, and if you run a crazy stuff, it can exceed easily, and may
result in the access of the invalid memory address -- this is what
syzkaller detected in a bug report.
As a fix, let the code graduate from naiveness, simply remove the loop
timeout.
When a sequencer queue is created in snd_seq_queue_alloc(),it adds the
new queue element to the public list before referencing it. Thus the
queue might be deleted before the call of snd_seq_queue_use(), and it
results in the use-after-free error, as spotted by syzkaller.
The fix is to reference the queue object at the right time.
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPIs come in as HVI not EE, so we need to test the appropriate
SRR1 bits. The encoding is such that it won't have false positives
on P7 and P8 so we can just test it like that. We also need to handle
the icp-opal variant of the flush.
Fixes: d74361881f0d ("powerpc/xics: Add ICP OPAL backend") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three tiny changes to the ERAT flushing logic: First don't make
it depend on DD1. It hasn't been decided yet but we might run
DD2 in a mode that also requires explicit flushes for performance
reasons so make it unconditional. We also add a missing isync, and
finally remove the flush from _tlbiel_va as it is only necessary
for congruence-class invalidations (PID, LPID and full TLB), not
targetted invalidations.
Fixes: 96ed1fe511a8 ("powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c63c2454ef incorrectly assumed that returning -ENOIOCTLCMD would
cause the native ioctl to be called. The ->compat_ioctl callback is
expected to handle all ioctls, not just compat variants. As a result,
when using 32-bit userspace on 64-bit kernels, everything except those
three ioctls would return -ENOTTY.
Fixes: 4c63c2454ef ("btrfs: bugfix: handle FS_IOC32_{GETFLAGS,SETFLAGS,GETVERSION} in btrfs_ioctl") Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
caused a problem on older controllers which do not support MSI-x (namely
ASR3405,ASR3805). This patch conditionalizes the previous patch to
controllers which support MSI-x
Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang") Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter kindly reported:
<quote>
The patch d27a7cb91960: "zfcp: trace on request for open and close of
WKA port" from Aug 10, 2016, leads to the following static checker
warning:
drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port()
warn: 'req' was already freed.
1613 out:
1614 spin_unlock_irq(&qdio->req_q_lock);
1615 if (req && !IS_ERR(req))
1616 zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id);
^^^^^^^^^^^
Use after free.
1617 return retval;
1618 }
Same thing for zfcp_fsf_close_wka_port() as well.
</quote>
Rather than relying on req being NULL (or ERR_PTR) for all cases where
we don't want to trace or should not trace,
simply check retval which is unconditionally initialized with -EIO != 0
and it can only become 0 on successful retval = zfcp_fsf_req_send(req).
With that we can also remove the then again unnecessary unconditional
initialization of req which was introduced with that earlier commit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a389fcfd2cb5 ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
added the proper mb(), but removed the test "prev_write_sz < pending_sz"
when making the signal decision.
As a result, the guest can signal the host unnecessarily,
and then the host can throttle the guest because the host
thinks the guest is buggy or malicious; finally the user
running stress test can perceive intermittent freeze of
the guest.
This patch brings back the test, and properly handles the
in-place consumption APIs used by NetVSC (see get_next_pkt_raw(),
put_pkt_raw() and commit_rd_index()).
Fixes: a389fcfd2cb5 ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
Signed-off-by: Dexuan Cui <decui@microsoft.com> Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com> Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Rolf Neugebauer <rolf.neugebauer@docker.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signal the host when we determine the host is to be signaled -
on th read path. The currrent code determines the need to signal in the
ringbuffer code and actually issues the signal elsewhere. This can result
in the host viewing this interrupt as spurious since the host may also
poll the channel. Make the necessary adjustments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Rolf Neugebauer <rolf.neugebauer@docker.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signal the host when we determine the host is to be signaled.
The currrent code determines the need to signal in the ringbuffer
code and actually issues the signal elsewhere. This can result
in the host viewing this interrupt as spurious since the host may also
poll the channel. Make the necessary adjustments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Rolf Neugebauer <rolf.neugebauer@docker.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the factors that can result in the host concluding that a given
guest in mounting a DOS attack is if the guest generates interrupts
to the host when the host is not expecting it. If these "spurious"
interrupts reach a certain rate, the host can throttle the guest to
minimize the impact. The host computation of the "expected number
of interrupts" is strictly based on the ring transitions. Until
the host logic is fixed, base the guest logic to interrupt solely
on the ring state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Rolf Neugebauer <rolf.neugebauer@docker.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ieee80211_ie_split_vendor doesn't return 0 on errors. Instead
it returns any offset < ielen when WLAN_EID_VENDOR_SPECIFIC is found. The
return value in mesh_add_vendor_ies must therefore be checked against
ifmsh->ie_len and not 0. Otherwise all ifmsh->ie starting with
WLAN_EID_VENDOR_SPECIFIC will be rejected.
A previous change to fix checks for NL80211_MESHCONF_HT_OPMODE
missed setting the flag when replacing FILL_IN_MESH_PARAM_IF_SET
with checking codes. This results in dropping the received HT
operation value when called by nl80211_update_mesh_config(). Fix
this by setting the flag properly.
Fixes: 9757235f451c ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value") Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[rewrite commit message to use Fixes: line] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're using non-canonical addresses in drm_mm, and we're making sure that
userspace is using canonical addressing - both in case of softpin
(verifying incoming offset) and when relocating (converting to canonical
when updating offset returned to userspace).
Unfortunately when considering the need for relocations, we're comparing
offset from userspace (in canonical form) with drm_mm node (in
non-canonical form), and as a result, we end up always relocating if our
offsets are in the "problematic" range.
Let's always convert the offsets to avoid the performance impact of
relocations.
Fixes: a5f0edf63bdf ("drm/i915: Avoid writing relocs with addresses in non-canonical form") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michel Thierry <michel.thierry@intel.com> Reported-by: Michał Pyrzowski <michal.pyrzowski@intel.com> Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170207195559.18798-1-michal.winiarski@intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 038c95a313e4ca954ee5ab8a0c7559a646b0f462) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Asynchronous external abort is coded differently in DFSR with LPAE enabled.
Fixes: 9254970c "ARM: 8447/1: catch pending imprecise abort on unmask". Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a long standing bug where the commit phase
of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference
leak if se_cmd->scsi_status returned non SAM_STAT_GOOD.
This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.
To address this bug, compare_and_write_post() has been changed
to drop the incorrect !cmd->scsi_status conditional that was
preventing *post_ret = 1 for being set during non SAM_STAT_GOOD
status.
This patch has been tested with SAM_STAT_CHECK_CONDITION status
from normal target_complete_cmd() callback path, as well as the
incoming __target_execute_cmd() submission failure path when
se_cmd->execute_cmd() returns non zero status.
Reported-by: Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Tested-by: Gary Guo <ghg@datera.io> Cc: Gary Guo <ghg@datera.io> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a long-standing bug with multi-session
(eg: iscsi-target + iser-target) se_node_acl dynamic free
withini transport_deregister_session().
This bug is caused when a storage endpoint is configured with
demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1)
initiators, and initiator login creates a new dynamic node acl
and attaches two sessions to it.
After that, demo-mode for the storage instance is disabled via
configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and
the existing dynamic acl is never converted to an explicit ACL.
The end result is dynamic acl resources are released twice when
the sessions are shutdown in transport_deregister_session().
If the storage instance is not changed to disable demo-mode,
or the dynamic acl is converted to an explict ACL, or there
is only a single session associated with the dynamic ACL,
the bug is not triggered.
To address this big, move the release of dynamic se_node_acl
memory into target_complete_nacl() so it's only freed once
when se_node_acl->acl_kref reaches zero.
(Drop unnecessary list_del_init usage - HCH)
Reported-by: Rob Millner <rlm@daterainc.com> Tested-by: Rob Millner <rlm@daterainc.com> Cc: Rob Millner <rlm@daterainc.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug where incoming task management requests
can be explicitly aborted during an active LUN_RESET, but who's
struct work_struct are canceled in-flight before execution.
This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync()
for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work
for target_tmr_work() never getting invoked and the aborted TMR
waiting indefinately within transport_wait_for_tasks().
To address this case, perform a CMD_T_ABORTED check early in
transport_generic_handle_tmr(), and invoke the normal path via
transport_cmd_check_stop_to_fabric() to complete any TMR kthreads
blocked waiting for CMD_T_STOP in transport_wait_for_tasks().
Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier
into transport_generic_handle_tmr() so the existing check in
core_tmr_drain_tmr_list() avoids attempting abort the incoming
se_tmr_req->task_cmd->work if it has already been queued into
se_device->tmr_wq.
Reported-by: Rob Millner <rlm@daterainc.com> Tested-by: Rob Millner <rlm@daterainc.com> Cc: Rob Millner <rlm@daterainc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the missing target_complete_cmd() SCSI status
parameter change in target_xcopy_do_work(), that was originally
missing in commit 926317de33.
It correctly propigates up the correct SCSI status during
EXTENDED_COPY exception cases, instead of always using the
hardcoded SAM_STAT_CHECK_CONDITION from original code.
This is required for ESX host environments that expect to
hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios,
and SAM_STAT_CHECK_CONDITION results in non-retriable
status for these cases.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Cc: Nixon Vincent <nixon.vincent@calsoftinc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the v4.2+ RCU conversion to se_node_acl->lun_entry_hlist,
a BUG_ON() was added in core_enable_device_list_for_node() to
detect when the located orig->se_lun_acl contains an existing
se_lun_acl pointer reference.
However, this scenario can happen when a dynamically generated
NodeACL is being converted to an explicit NodeACL, when the
explicit NodeACL contains a different LUN mapping than the
default provided by the WWN endpoint.
So instead of triggering BUG_ON(), go ahead and fail instead
following the original pre RCU conversion logic.
Reported-by: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com> Cc: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_atomic_helper_page_flip and drm_atomic_ioctl set their own events
in crtc_state->event. But when it's set the event is freed in 2 places.
Solve this by only freeing the event in the atomic ioctl when it
allocated its own event.
This has been broken twice. The first time when the code was introduced,
but only in the corner case when an event is allocated, but more crtc's
were included by atomic check and then failing. This can mostly
happen when you do an atomic modeset in i915 and the display clock is
changed, which forces all crtc's to be included to the state.
This has been broken worse by adding in-fences support, which caused
the double free to be done unconditionally.
[IGT] kms_rotation_crc: starting subtest primary-rotation-180
=============================================================================
BUG kmalloc-128 (Tainted: G U ): Object already free
-----------------------------------------------------------------------------
Add the missing INTEL_OUTPUT_DP_MST case in bxt_get_dpll()
to correctly initialize the crtc_state and port plls when
link training a DP MST monitor on BXT/APL devices.
Fixes: a277ca7dc01d ("drm/i915: Split bxt_ddi_pll_select()")
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=99572 Reviewed-by: Cooper Chiou <cooper.chiou@intel.com> Reviewed-by: Gary C Wang <gary.c.wang@intel.com> Reviewed-by: Ciobanu, Nathan D <nathan.d.ciobanu@intel.com> Reviewed-by: Herbert, Marc <marc.herbert@intel.com> Reviewed-by: Bride, Jim <jim.bride@intel.com> Reviewed-by: Navare, Manasi D <manasi.d.navare@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1486096329-6255-1-git-send-email-shawn.c.lee@intel.com
(cherry picked from commit 0aab2c721d81590012a5021a516f00666646741f) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-4.9.git / log